The Best Btus For Gas Dryer

This kit contains 48 IN yellow coated corrosion resistant SS gas connector with 1/2 IN FIPx1/2 IN MIP-tapped 3/8 IN FIPx1/2 IN MIP SmartSense EFV & TS adapters, thread sealant, leak solution. This CSA approved gas connector is commonly used on home appliances like gas dryers. SmartSense used with Dormont coated gas connectors gives an industry leading 3 Levels of Protection. This 1/2 IN OD flarex1/2 IN MIP SmartSense excess flow valve and thermal shut off is an intricately-designed valve with two primary components, a gas flow-limiting plunger and thermal shutoff sensing ring. SmartSense detects and activates in the event of gas line rupture, disconnection, or fire. The plunger limits gas flow protecting against excessive gas leaks in the event of full-line rupture or disconnect. SmartSense self resets to the standard rate of flow after gas line restoration and pressure equalization. The internal thermal ring expands to stop gas flow for temperatures ranging from 350 to 425 degrees F.

BrassCraft’s Safety+PLUS gas connector combines patented excess flow technology with the advanced corrosion resistance, to provide a safer gas connector for your home and family. In the event of a gas line rupture or disconnect, the Safety+PLUS Excess Flow Valve (EFV) restricts gas flow at the appliance to a non-hazardous level. This immediate action helps avert the potential for a dangerous release of gas into the home. Gas is controlled only at the point where the problem exists; the rest of your system will continue to function. Safety+PLUS Excess Flow Valve (EFV) automatically resets once the gas line is properly repaired. BrassCraft’s stainless steel gas connector also features a proprietary polymer coating designed to withstand prolonged exposure to harsh household cleaning, plumbing repair and masonry products as well as UV rays and salt. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly on the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested to provide the most complete corrosion resistance. California residents: see Proposition 65 information 1/4 in. I.D. (3/8 in. O.D.) corrugated stainless steel Safety+PLUS EFV helps protect against gas fires and explosions Safety+PLUS EFV installs like a standard gas fitting; no special tools required Use to install dryers, decorative stoves and gas log fireplaces ProCoat coating corrosion resistant to harsh chemicals as well as UV rays and salt CSA certified to ANSI Z21.24/CSA 6.10 and ANSI Z21.75/CSA 6.27 Approved for indoor and outdoor use 3/8 in. female flare (1/2 in. MIP external threads) connection to gas supply or gas ball valve Safety+PLUS EFV has no parts that can wear, break or misalign over time for 24/7 protection Safety+PLUS EFV is omnidirectional and can be installed in any position – vertical or horizontal

The Di and Drew Dryer Vent Brush Cleaner Kit is a must have tool for every homeowner 

*Over time lint builds up in the dryer vent, causing your dryer to work extra hard to dry, increasing electric use and the cost of your electric bill.

*House fires from lint buildup is the leading cause of fires in homes, and according to FEMA, it’s estimated that 2,900 home clothes dryer fires are reported each year and cause an estimated 5 deaths, 100 injuries, and $35 million in property loss.

*Professional lint removal is expensive and can cost hundreds of $$ and must be done yearly.

*Our Dryer vent cleaning kit is suitable for multiple uses. These highly flexible rods work well for fireplaces, exhaust vents, kitchen vents and so much more.

Why You Will Love The Di and Drew Dryer Vent Cleaner Kit

*Easy to use with simple instructions, and can be reused for years to come at fraction of the cost of hiring a professional.

*Our kit extends up to 20 feet to allow you to get to hard to reach places without purchasing extra kits.

*Always turn clockwise to avoid disconnecting the rods while in use inside of a duct.

*A drill is optional, but with our bonus drill adapter, it’s quicker and easier to clean your vents.  Please note that when using a drill, make sure to spin the brush at a low speed to prevent any chance of tearing a vent.

What’s Included

*One 4” premium synthetic nylon brush head

*Fourteen Flexible, durable screw rods

*Bonus Drill Adapter

 Special Sale Ending Soon… Buy Now!

Duratrac gas connectors are CSA certified to ANSI Z21.24 CSA/CGA 6.10 Standard connectors for gas appliance and ANSI Z21.75 CSA/CGA 6.27 Standard Connectors for outdoor gas appliance and manufactured homes. The corrosion resistant yellow coating protects the product from exposure from harsh weather and certain chemicals. Refer to chart for BTU rating.

Purchase tip: This item is for large Btu demand appliances requiring 1″ OD pipe diameter and 3/4″ end fittings, applicable for appliances such as tankless water heater (over 150,000 Btu), commercial tank water heater, large space heater, large furnace, commericial fryer, commercial dryer, commericial oven, and commercial restaurant equipments. For smaller appliances such as 30, 40, 50, 75, 100 gallon residential gas water heaters, oven, cooktop, small tankless water heater less than 150,000 Btu, residential dryer, residential fire place, residential furnace and space heater use 1/2″ OD pipe diameter with 1/2″ fittings. 

Perfect for gas logs, garage heaters, gas stoves and wall mounted heaters. Size: 3/8 inch, Compatible With: Heaters, logs, ranges, dryers, etc., Product Type: Connection kits, Fuel Type: Propane/natural gas

This is a Flextron gas connector from their YC34 series of connectors, which is designed for indoor and is designed as part of a tank less water heater or -valve kit. it has an outer diameter of 1" and an inner diameter of 3/4" and is made of stainless steel coated with a yellow epoxy coating along the entire length of the connector. the coating gives it extra protection against corrosion when it comes in contact with chemicals that are typically found in households. on the ends of this 36" long connecter are a 3/4" fip and a 3/4" mip fitting, made of zinc-plated stainless steel type s45c. the connector is rated for use in the temperature range of -40 f to 150 f and it is certified by csa for use up to a pressure of 0.5 psi. please consult the product information for the flow capacity for this part, for natural gas. the part is certified by commonwealth of Massachusetts, the city of new York and by upc and csa for meeting the amse A112.18.6 and ansi Z21.24, Z21.69 and Z21.75 gas appliances and manufactured homes standards. each connector is 100% tested on leaks before it leaves the factory. the design has been tested on strength and it can withstand an internal hydrostatic pressure of 250 psi or 17 mpa without bursting or showing signs of leaks. it can also endure up to 30 bends without leaks in water at a depth of maximum 2 inches and withstands 15 twists of 90 degrees, without showing signs of corrosion. its flared end fittings result in a metal to metal seal, which is tested to be leak free within a tighten torque of 1040 inch-pounds. the connector can handle external temperatures of 800 f.

Product Description

LASCO 10-1215 LASCO 10-1215 Flexible Coated Gas Appliance Supply Line, 72-Inch, 3/8-Inch OD Connector with 1/2-Inch MIP X 1/2-Inch FIP Fittings. For indoor or outdoor use. Yellow safty coating – corrugated stainless steel. For use with natural gas or propane. Connect to gas dryers! Larsen Supply a third generation family owned and operated company with over 80 years of experience has the largest retail plumbing line in the industry today with over 7000 packaged and 16,000 bulk SKU’s. We pride ourselves on service, selection and support! All Lasco merchandise if warranted to be free of manufacturing defects. Please revert to retail place of purchase for resolution of any possible plumbing questions, warranty or defective part replacement.

From the Manufacturer

LASCO 10-1215 Flexible Gas Dryer Connector Line, 3/8-Inch Diameter with 1/2-Inch Fittings, 72-Inch Long. 3/8-Inch X 72-Inch Gas Appliance Connector, Flexible Stainless Steel, Safety Coating, 1/2-Inch Pipe Thread Ends. Indoor or outdoor use. Yellow Safety Coated. Corrugated Stainless Steel. For Use With Natural Gas or Propane. To Connect Gas Dryers.

Along with everything needed for installing most gas appliances
On/off valve provides easy servicing of appliances or summer shutdown
5 Pieces kit includes: 22″ stainless flexible gas connector
1/2″female flare at both ends
1/2″ male Flare x 1/2″ NPT
1/2″ male flare x 3/8″ male NPT
1/2″ male flare x 3/8″ female NPT
Brass shut-off valve with 1/2″ female NPT x 1/2″ male flare
Fit for gas logs, garage heaters, gas stoves and wall mounted heaters

Product Description

Brass Craft’s 3/8 In. FIP x 3/8 In. MIP x 60 In. Recoat Gas Appliance Connector is 3/8 In. OD (1/4 In. ID) tube with a maximum operating capacity of 24,900 BTU’s. This Recoat stainless steel gas connector is engineered with added safety in mind. The proprietary polymer coating is designed to withstand prolonged exposure to harsh household chemicals, UV rays and salt. Recoat is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the Recoat coating is baked directly onto the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

From the Manufacturer

BrassCraft’s 3/8 In. FIP x 3/8 In. MIP x 60 In. ProCoat Gas Appliance Connector is 3/8 In. OD (1/4 In. ID) tube with a maximum operating capacity of 24,900 BTU’s. This ProCoat stainless steel gas connector is engineered with added safety in mind. The proprietary polymer coating is designed to withstand prolonged exposure to harsh household chemicals, UV rays and salt. ProCoat is applied to the corrugated stainless steel connector using advanced powder-coat technology. Unlike conventional dipped or sprayed coatings, the ProCoat coating is baked directly onto the connector surface at high temperatures to provide a uniform coating over the entire length of the connector. The coating is applied only after the connector has been 100% leak tested, prior to nut and fitting assembly. This process results in the most complete corrosion resistance available.

The Flextron Steel Male gas fitting adapts gas connector nut to appliance inlet or gas supply. These fittings are from FTGC-34 series and manufactured from solid bar stock for a seamless, durable design. The flared end of the fitting connects to the gas connector nut. The male end connects to the gas appliance inlet, gas ball valve or gas supply stub out. Threads create a cold weld with the end of the gas connector, making a strong and leak tight seal. This Fitting is used with 1 inch outer diameter flare x 3/4 inch (MIP) male iron pipe (TAPPED 1/2″). Gas connector adaptor fitting for appliances with moderate BTU demands such as a four-burner stove, water heater or dryer.