The Best Dryer Booster Fan Installation

Only DEDPV fan kit in the market: To run the full cycle of the dryer rather than resorting to periodic on/off cycling. That can be installed in any orientation with no calibration needed. That allows for flush mounted remote indicator. The DRM04 Dryer Booster Fan Kit is a Dryer Exhaust Duct Power Ventilator (DEDPV) designed for compliance to UL Standard 705. Any UL705 DEDPV is only suitable for residential electric clothes dryers employing 4” ductwork. Suncourt accepts no responsibility for use of this product in other applications. DRM04 Kit Contains:(x1) TFM04 4” corded metal centrifugal fan with monitor(x1) TFR100 remote operation indicator(x1) English and French TFR100 warning card(x35’) of 22 gauge 5-conductor wire(x1) CS100 clip-on clothes dryer current sensor with 6’ cord(x2) 4” metal cleanout sleeves with band clamps(x4) self-adhesive foam strips (to limit vibration transferred to ductwork) Screwpack Contents: (x4) 1/4” x 1 1/2” lag bolts (mounting the fan) (x4) 1/4” washers (mounting the fan) (x4) 3/8” rubber grommets (lag bolt vibration isolation) (x2) 6-32 x 1 1/2” machine screws (for mounting remote indicator to electrical box) (x2) #6 x 1 1/2” sheetmetal screws (for mounting remote indicator flush to drywall) (x2) #6 7/8” long wall anchors (for mounting remote indicator flush to drywall) (x3) self-adhesive cord clips (for securing low-voltage signal wiring) Tools / supplies you will need: 3/16” drill bit (wall anchors if remote is flush-mount, pilot holes for lag bolts). 7/16” socket and ratchet (to tighten lag bolts). Phillips screwdriver (for mounting remote indicator). Flathead screwdriver or 5/16” nut driver (for cleanout band clamps). Sheetmetal shears. Foil duct tape. Wire cutters (to cut slot in operation indicator if flush-mounted). Wire strippers (to cut low-voltage wire to length and strip if need

When the dryer exhaust has a long run to the vent it increases drying time as well as wear and tear on the dryer. The DryerJet has been tested on runs up to 50 feet of duct and up to four 90° bends. Testing was done by an independent lab at Florida International University. Click on picture for dimensional diagram. No wiring necessary, just plug it in! Fully Automatic Operation. Features the PS-35 Pressure Switch mounted on unit completely wired to the 10-foot line cord. Auto operation with adjustable pressure switch wired to a 10, 115 volt power cord. Ball bearing motor OUT of airstream. No lint on motor. Install next to dryer or anywhere in the line – Tested to CSA standard C22.2 113-M 1984.

Versatile and durable the DBM4 exhaust/intake/booster fan features an enclosed motor and quality construction that allows low noise and extremely low power usage (18 Watts). this is an excellent choice for increasing air flow through 4 inch ducting. This fan contains a 110 cfm and comes with a 6 foot power cord.

The Fantech dryer exhaust fans have been specially designed to solve the problems caused by long duct runs on clothes dryers. According to dryer manufacturers and some local building codes, exhaust fans should be added in the dryer duct run when the length of the duct exceeds 35 feet with no bends, 30 feet with one bend or 25 feet with two bends.

The fans feature a fully sealed plastic housing. The housing is joined via a vibration welding process. The process uses transverse, reciprocating motion at the point of contact between the housing’s inlet and outlet pieces. The friction produces heat that melts the thermoplastic material at the interface. The melted material quickly re-solidifies, resulting in a fused, single-piece housing. The fused seam is inherently air tight, very strong and permanent. No screws or adhesive is used to join the housing pieces. An air-tight fan ensures that efficiency is not lost and contaminants are not spilled due to leakage.

Tagview AC Current Switch is designed for AC current monitoring, motor overload protection, automatic control system and other applications. This device senses a current draw of between 1amp and 50 amps and closes a set of contacts while AC current is passing through sensor.

Main Specifications:
Enclosure Dimensions(LxWxH): 88 x 25 x 50mm; Or approx. 3.46 x 0.98 x 1.97 inch
Sensor Hole Diameter: 20mm (0.79 inch)
Mounting Holes: 2x5mm holes spaced 76mm on base (2 x 0.19”holes spaced 3”on base)
Switch Rating: 2.5 A @ 120 V AC
Contact Type：Normally Open
Operating Temperature: -20 to 45℃（-4 to 113℉）
Humidity Limits: 0-95% RH, non-condensing
Response Time: ≤200ms
Accuracy: 1%
Hysteresis: ≤1%

NOTE:
1. Disconnect and lock-out all power sources prior to installation.
2. The current switch has a rating of 2.5 Amps maximum at 120 Volts. If the secondary device (which is conncted with the switch) draws more than 2.5 Amps, then you will need a separate high current relay.

Package includes:
1x AC Current Switch
1x Instruction Manual

Warranty:
1-year free replacement or full refund without return.
If the item you have received is defective in any way, please message us for free replacement or refund without return.