Nowadays, there are so many products of interior dryer vent box in the market and you are wondering to choose a best one.You have searched for interior dryer vent box in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings interior dryer vent box which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
978 reviews analysed
1. Deflecto Dryer Lint Trap Kit, Supurr-Flex Flexible Metallic Duct
Feature
- Not Applicable
- Imported
- Designed for safe indoor dryer venting where outside venting is impossible
- Quick, easy installation, fits most clothes dryer (not for use with gas dryers)
- If used in small rooms, open doors for adequate distribution of heat and moisture
- Lint trap requires 4 cups (32 oz.) of water for use
- Transition duct, 2 clamps and lint trap are included
Description
Product Description
“
Product Description
Indoor dryer venting Supurr-Flex UL listed 2158 clothes dryer transition duct non-tipping 2 clamps 4′ dia x 5-ft length foil duct built-in hanger. Designed for safe indoor dryer venting where outside venting is impossible. Quick, easy installation, fits most clothes dryer (not for use with gas dryers). If used in small rooms, open doors for adequate distribution of heat and moisture. Lint trap requires 4 cups of water for use. Transition duct, 2 clamps and lint trap are included. Imported.
From the Manufacturer
This is a genuine replacement part. The model number and name for the following item is: Deflecto LTF Lint Trap.
“
From the Manufacturer
This is a genuine replacement part. The model number and name for the following item is: Deflecto LTF Lint Trap.
2. BetterVent Indoor Dryer Vent Kit – Protect Indoor Air Quality and Save Energy with a Superior Dryer Lint Filter (Electric Dryers Only)
Feature
- INDOOR DRYER VENT LINT TRAP – Double filter system captures lint and dust for healthier indoor environment. The stainless steel screen acts as a pre-filter capturing large lint particles, pet hair, etc. and can be cleaned with a sweeping motion of the hand. The polyester filter will capture the finer lint dust and can be vacuumed clean for extended use or replaced when fully loaded with lint. Compatible with electric dryers only.
- SAVE ENERGY – Clothes dry faster, saving time and energy. Savings increase in colder months by returning warm dryer air into the room.
- NO WATER NEEDED – This patented double filter system does not use water, eliminating messy cleanups.
- SAFETY ALERT FEATURE – There is a patent pending Safety Vent Flap designed to open, as a reminder to clean the screen and filter. This is a great solution for renters or homeowners concerned with dryer lines that exceed the dryer manufacturer’s recommendations, resulting in inefficient operation and lint accumulation.
- MADE IN USA – Manufactured in the United States of America. All installation hardware included.
Description
This indoor dryer vent is designed to capture the lint from your electric clothes dryer, for those unable to vent to the outside. All types of indoor dryer vents will allow heat and humidity into the room. We recommend the user allow for air circulation and ventilation when operated in confined spaces. This patented double filter system does not use water, eliminating messy cleanups. The stainless steel screen acts as a pre-filter capturing large lint particles, pet hair, etc. and can be cleaned with a sweeping motion of the hand. The polyester filter will capture the finer lint dust and can be vacuumed clean for extended use or replaced when fully loaded with lint. Replacement filters are available in packages of 6, lasting most users up to a year under normal conditions. There is a patent pending “safety vent flap” designed to open, as a reminder to clean the screen and filter. For renters or homeowners concerned with dryer lines that exceed the dryer manufacturer’s recommendations, resulting in inefficient operation and lint accumulation, this is a great solution. Saves energy in colder months by returning warm dryer air into the room. All installation hardware included. Customer supplies hose and clamps. Installation is quick and easy, instructions included. If you’ve purchased this product in the last 30 days and one or both of the side clips is broken, please reach out to [email protected] for a replacement.
3. Dryer Dock Dryer Vent 6" for 4" Tubes, White
Description
Dryer Dock Dryer Vent 6″ for 4″ Tubes, White
4. Dundas Jafine TDIDVKZW Indoor Dryer Vent Kit with 4-Inch by 5-Foot Proflex Duct, 4 Inch White
Feature
- Can be used to vent your electric clothes dryer indoors when outdoor venting is not possible
- Includes 4-inch by 5-foot ProFlex dryer transition duct, plastic lint reservoir, 2 plastic adjustable clamps
- Ideal for apartments, condominiums and RVs
- ProFlex dryer transition duct UL approved for safe dryer venting
- Not be used with gas clothes dryers
Description
Product Description
Dundas Jafine TDIDVKZW ProFlex Indoor Dryer Vent Kit with 4-Inch by 5-Foot ProFlex Duct
From the Manufacturer
This ProFlex indoor dryer vent kit includes a 4-inch by 5-foot UL 2158A listed and marked ProFlex transition duct, a plastic lint reservoir, and 2 plastic clamps. This item is used to vent your electric dryer indoors when outside venting is not possible. It is ideal for apartments, condominiums, and RVs Never use this product with a gas clothes dryer.
5. MagVent MV-90 Magnetic Dryer Vent Coupling
Feature
- For 90° Venting, or Vent Pipes Exiting Side Wall, Floor or Ceiling in New & Existing Construction.
- Strong Magnets Self-Align & Attach Dryer Hose to Exit Vent.
- Utilizes Zero Flame Spread, UL 2158A Approved Dryerflex Transition Hose.
- Shorter Dryer Hose & More Rigid Metal Pipe Reduces Drying Time & Utilities…It Pays For Itself!
- Easy, Solid Installs that Boost Dryer Efficiency & Safety!
Description
The MV-90 is designed for when the vent path takes a 90 degree turn, such as down through the floor, up through the ceiling, or off to the side. -The MV-90 can handle offsets up to 3 inches from center to center. The more accurately you line up the MV-90 with the vent on the back of your dryer, the better the vent path and the further back you can locate your dryer. Normally, the MV-90 requires 5 1/2 inches of clearance behind the dryer. If an obstruction necessitates you locate the MV-90 at the maximum 3 inch offset, then your dryer will need to sit out an additional 3 inches to allow for a bend radius in the transition duct. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 6-9 inches): The MV-90 can be coupled directly to a standard 4 inch diameter, adjustable, 90 degree elbow which creates a 9 inch offset. See photo below. If your same wall offset is 6 inches, you can use the MV-90 and an elbow, taking advantage of its ability to handle misalignment up to 3 inches. -Same wall offsets greater than 9 inches: Simply mount the MV-90 directly behind your dryer, plug the 90 degree elbow into the wall vent, and measure for the required length of rigid metal pipe between them. Make sure to measure from where the pipe will stop on the MV-90 to the stop on the male end of the rigid metal pipe. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 0-3 inches): If your same wall offset is between 0 and 3 inches, then the MV-180 is the product for you.
6. Gardus DVME Dryer Vent Made Easy, Increase Your Dryer’s Efficiency & Safety, Easily Connect Dryer to Dryer Vent, Eliminate Bulky Flex Pipe, ICC-ES PMG Listed
Feature
- Ensures Safety – Instantly reduces the risk of dryer fires in your home by eliminating kinked, lint-filled dryer flex pipe! Provides easy access for routine dryer vent cleaning!
- Increases Efficiency – Increases your dyer’s efficiency saving you money and helping our environment!
- Saves Space – Reclaims lost inches of space in your laundry area caused by bulky dryer flex pipe while positioning your dryer tightly to the venting wall!
- Easy Installation – Simply slide the dryer into the rubber seal in the wall without reaching behind to make the connection and flush up the fronts of your washer and dryer
- Designed for installations with the dryer vent on the wall behind the dryer
- Ideal for new construction and remodels
- Made in the USA – ICC-ES PMG Listed ensuring code compliance and manufactured in the USA from high-heat ABS plastic coupled with a Sarlink gasket and stainless steel clamps
Description
Dryer Vent Made Easy eliminates the wasted space behind your dryer caused by bulky flex pipe. With Dryer Vent Made Easy, simply slide the dryer into the rubber seal in the wall without reaching behind to make the connection. It allows your dryer to push tight to the wall and flushes up the front of your washer and dryer. Our product increases your dryer’s efficiency and safety which saves you money and helps our environment. Welcome to the future of dryer vent installation. Made in the USA.
7. Essential Values 6 Pack Compatible Replacement Filters for Bettervent Indoor Dryer Vent
Feature
- BEST VALUE – Our 6 Pack Of Fine Polyester Replacement Filters Are Cost Effective And Efficient For Maintaining The Dirty Lint Build Up That Can Accumulate In Your Dryer Vent.
- IMPROVES AIR QUALITY – Keep Your Dirty Air Cleaner Than Ever By Protecting Your Home From Unwanted Bacteria & Other Unfriendly Dust Particles.
- HASSLE FREE – Changing Filters Is No Longer A Burden. It NOW Takes Seconds To Ensure Best Quality Air – ONLY 3 Easy Steps!
- MAXIMIZE SAVINGS – Our Dryer Vent Filter Replacements Are Engineered To MAXIMIZE Savings By Improving Air Circulation In Home. Also Vacuum Friendly, Highly Improve The Life Of Your Filters With Weekly Upkeep.
- MADE IN USA – Designed & Built to Fit BetterVent Indoor Dryer Vent Systems. Our Polyester Replacement Filter Is Measured 7″ X .75 X 8.25″ Inches. Similar Product As Other Brands, But Now A Fraction Of The Price! **** Vacuumed Sealed For Air Tight Space Saving Experience. Filters Expand After 12 HRS Of Opening, Okay To Use Immediately!****
8. Deflecto Dryer Vent, Wide Mouth Galvanized Vent Hood, 4”, Silver (GVH4NR)
Feature
- 4″ diameter opening
- Includes 4″ super guard vent hood with removable guard, aluminum pipe and collar Removable bird guard helps prevent birds and rodents from entering home through dryer vents
- Hood louvered dampers operates quietly for maximum exhaust flow and seal when not in operation to help prevent back drafts Durable, weather resistant, limited lifetime guaranteed
- Model number: GVH4NR
9. Deflecto Supurr-Vent Louvered Outdoor Dryer Vent Cover, 4 Inches Hood, White (HS4W/18)
Feature
- 4″ (10.2cm) diameter vent opening
- 6″ x 6″ total unit size
- Helps keep wind, rain and snow from entering outdoor dryer vents
- Dryer vent cover is easy to install and opens with ease for maximum exhaust flow
- Features curved louvers for quieter operation
- Durable and weather-resistant with UV inhibitor added to hood to prevent sun damage and cracking
Description
The Deflecto Supurr-Vent Louvered Dryer Vent Hood Cover helps keep wind, rain and snow from entering outdoor dryer vents. The vent cover is easy to install and features curved louvers for quieter operation. Opens with ease for maximum exhaust flow, and it is durable and weather-resistant with UV inhibitor added to hood to prevent sun damage and cracking.
Conclusion
By our suggestions above, we hope that you can found Interior Dryer Vent Box for you.Please don’t forget to share your experience by comment in this post. Thank you!
