The Best Liftmaster Garage Door Springs

WARNING: Torsion springs, extension springs, and related door hardware can cause serious injury or death if not handled and installed properly. Professional installation is recommended. Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Read and understand all instructions before you begin work. Extension and torsion springs, along with attached hardware, are under extreme tension at all times. All tension must be released from springs before any work is performed.

Product Description

Use this steel right hand wound torsion spring to replace broken garage door springs. It includes stationary and winding cones with .243” wire size x 2 “ inside dimension x 32” length with yellow color code. This torsion spring is a regular duty spring with an estimated lifetime rating of 10,000 cycles. These types of torsion springs provide lifting force for heavy garage doors and must be selected by the spring’s dimensions, rather than the door’s weight. See the product specifications with illustrations found in Prime-Line’s Torsion Spring Selection Guide to assure that the proper replacement spring has been selected. Steel winding rods are used to wind and unwind the tension on torsion springs and they are the only tools recommended for this purpose. Two winding rods are required for torsion spring replacement. When dual spring installations are involved, it is important to correctly install both the left and right wind springs during the same job. In the case of dual spring installations, note that the proper use of RIGHT WIND and LEFT WIND springs is imperative. Also, when dual spring installations are involved, it is important to replace both springs, as replacing only one spring may add increased strain to the older non-replaced spring. As an important safety precaution: all broken or malfunctioning hardware should be replaced with matching hardware, without any modifications. Garage door torsion springs can cause serious injury if not handled and installed properly. If attempting to replace the torsion springs yourself, it is important that the removal or adjustment of torsion springs is not attempted with any other tool other than Prime-Line’s item number GD-52238. Failure to utilize Prime-Line’s item number GD-52238 for the replacement of these springs may result in severe personal injury. Note: To determine the handing of your torsion spring wind, look at the end of the spring with the ‘finger’ of the spring at the top of the wind. When the end of the spring is at 12:00 o’clock and it is pointing to the left, the spring is a right wind; if the end of the spring points to right (positioned at 12:00 o’clock) it is a left wind. When standing inside the garage looking outside, the torsion spring with the black painted winding cone installs on the right side of the door, and the torsion spring with the red painted winding cone installs on the left side of the door.

From the Manufacturer

This torsion spring is constructed of steel and it includes a stationary cone and a winding cone attached to opposite ends of the spring. These types of torsion springs provide lifting force for heavy garage doors and must be selected by the spring’s dimensions, rather than the door’s weight. See the product specifications with illustrations found in Prime-Line’s Torsion Spring Selection Guide to assure that the proper replacement spring has been selected. In the case of dual spring installations, note that the proper use of LEFT WIND & RIGHT WIND springs is imperative. Also, when dual spring installations are involved, it is important to replace both springs, as replacing only 1 spring may add increased strain to the older non-replaced spring. This torsion spring is a regular duty spring with an estimated lifetime rating of 10,000 cycles. As an important safety precaution: all broken or malfunctioning hardware should be replaced with matching hardware, without any modifications. These garage door torsion springs can cause serious injury if not handled and installed properly. If attempting to replace the torsion springs yourself, it is important that the removal or adjustment of torsion springs is not attempted with any other tool other than Prime-Line’s item number GD-52238. Failure to utilize Prime-Line’s item number GD-52238 for the replacement of these springs may result in severe personal injury. These winding rods are used to wind and unwind the tension on torsion springs and they are the only tools recommended for this purpose. Note: To determine the handing of your torsion spring wind, look at the end of the spring with the ‘finger’ of the spring at the top of the wind. When the end of the spring is at 12:00 o’clock and it is pointing to the left, the spring is a right wind; if the end of the spring points to right (positioned at 12:00 o’clock) it is a left wind. When standing inside the garage looking outside, the torsion spring with the black painted winding cone installs on the right side of the door, and the torsion spring with the red painted winding cone installs on the left side of the door.

When ordering torsion srings you are required to choose from the tables A) Wire size B) Inside diameter C) The length of spring in inches  D) Wind of Spring (Right Hand Wound, Left Hand Wound or a Pair RHW and LHW.

When ordering torsion srings you are required to choose from the tables A) Wire size B) Inside diameter C) The length of spring in inches  D) Wind of Spring (Right Hand Wound, Left Hand Wound or a Pair RHW and LHW.

Extension Spring for 7′ High Door, 120 Pounds
120# Extension Springs – Green Springs
25-42-120 Extension Springs
Can be used on any door that weighs around 120 lbs.
Double Looped Ends
25″ Relaxed, 42″ Stretch,
Rated 120 Pounds Per Set
DASMA Color Coded; Green.

Heavy Duty Extension Spring 3″ Pulley and Safety Cable Complete Garage Door Set Keep your garage door running smooth and safe with new pulleys and safety cables. PAIR RESTRAINT CABLE, 3/32″ 7X7 120″ Two ———– Heavy Duty 3″ Pulleys Two ———– 3″ Clevis pulleys One ———– Pair safety cables Two ———– S-HOOK, 1/4″ X 2-1/2″ Two ———– CABLE ADJUSTMENT CLIP 200 lbs. load capacity and rated for 10,000 cycles Maximum cable diameter 5/32″; 3/8″ Bore

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.

WARNING: Torsion springs, extension springs, and related door hardware can causeserious injury or death if not handled and installed properly.Professional installation isrecommended.Do NOT attempt to install springs or hardware yourself unless you have the proper tools, reasonablemechanical aptitude and experience, and upper arm strength.Read and understand all instructionsbefore you begin work.Extension and torsion springs, along with attached hardware, are under extreme tensionat all times. All tension must be released from springs before any work is performed.

This 24″ Torsion Garage Door Spring 2-Pack is a torsion spring replacement for broken sectional garage door torsion springs. All our garage door torsion springs meet the DASMA
standard rating of 10,000+ door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation.Surface coated black to make sure springs
won’t rust in the open air.We also provide a pair of winding bars with unique non-slip handle,they will help you finish your work easier.
PACKAGE INCLUDE:
1x left-hand wind and 1x right-hand spring
.218’’ wire gauge
24″ coil-to-coil length
2″ inner spring diameter 2x winding bars with non-slip handle
DASMA WARNING:
HIGH SPRING TENSION CAN CAUSE SERIOUS INJURY OR DEATH.Professional installation is recommended. Do NOT attempt to install springs or hardware yourself unless you have the
proper tools, reasonable mechanical aptitude and experience, and upper arm strength. Extension and torsion springs, along with attached hardware, are under extreme tension at all
times. All tension must be released from springs before any work is performed.
IMPORTANT:Please purchase after confirming that the outer diameter, wire diameter and length are totally the same as the original product.Even a little change in size can result in different performance,so please check carefully before purchasing to avoid waste.