Top 10 Retrofit Dryer Vent Box

The Saf-T-Duct Dryer Outlet Box from Builder’s Best finishes off dryer vent rough-ins and easily adds or recaptures space in the wall behind your dryer for venting. The unit can be used in-wall (prior to drywall) or on-wall (after drywall is installed). The standard 4 in. round connections allow for the best airflow and connect easier than ovals.

Why The Need For The Dryer Box? In the past, homeowners had to put up with the inefficient venting of their dryer appliance exhaust due to numerous friction causing bends or kinks in the flex duct hose that connects the dryer to the wall exhaust pipe. Lint build up and a fire hazard are the unwelcome bi products of these annoying bends. In order to accommodate these flow restrictive bends, the dryer appliance had to be located five to six inches away from the wall, taking away from valuable living area. The Dryer Box solves these issues and provides much more in benefits to the builder, the contractor and the homeowner. What Are The Benefits Of The Dryer Box? Locate the dryer right up against the wall Flex is protected from getting squished No trim ring piece is needed Lint build up is minimized Efficiency is increased Dryer related service calls are almost eliminated Elbow eliminator gain 5 foot of duct run Doubles as gas connection receptacle Can be installed in One Hour wall Meets code requirements as a clean out Laundry room appears larger to prospects Surface is paintable, no masking needed Applauded by building inspectors Reduces the fire hazard Socks and clothing can t fall behind appliance Prevents costly punch out work to damaged 90 Eliminates mold potential Contributes 2 USGBC LEED credits Which Are The Specifications For The Dryer Box Model 425? Designed for upward exhaust direction 22 gauge aluminized steel weighing 4.14 pounds each Top port measures 4 1/8 with very slight oval shape Distance from nailing flange to rear of box is 4 1/4 Overall measurements: 21 h x 12 1/2 w x 5 1/8 deep Inside measures 9 1/2 wide x 18 1/4 tall.

Dvbox 17.38×11.5×4.5 Dryer Venting Box

The EZ Dryer Vent is a White metal box that attaches to the wall or floor on the back of a dryer, it connects to a magnetic boot on the dryer for easy connecting and disconnecting from the dryer vent. This gives you easy access to the back of your dryer to clean the ducts and retrieve lost items without crimping the duct each time. The EZ Dryer Vent comes with soft pads so the dryer moves easily. The EZ Dryer Vent is 10 inch x 10 inch x 4 inch and fits on most dryers and is easy to install.

The MV-90 is designed for when the vent path takes a 90 degree turn, such as down through the floor, up through the ceiling, or off to the side. -The MV-90 can handle offsets up to 3 inches from center to center. The more accurately you line up the MV-90 with the vent on the back of your dryer, the better the vent path and the further back you can locate your dryer. Normally, the MV-90 requires 5 1/2 inches of clearance behind the dryer. If an obstruction necessitates you locate the MV-90 at the maximum 3 inch offset, then your dryer will need to sit out an additional 3 inches to allow for a bend radius in the transition duct. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 6-9 inches): The MV-90 can be coupled directly to a standard 4 inch diameter, adjustable, 90 degree elbow which creates a 9 inch offset. See photo below. If your same wall offset is 6 inches, you can use the MV-90 and an elbow, taking advantage of its ability to handle misalignment up to 3 inches. -Same wall offsets greater than 9 inches: Simply mount the MV-90 directly behind your dryer, plug the 90 degree elbow into the wall vent, and measure for the required length of rigid metal pipe between them. Make sure to measure from where the pipe will stop on the MV-90 to the stop on the male end of the rigid metal pipe. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 0-3 inches): If your same wall offset is between 0 and 3 inches, then the MV-180 is the product for you.

Dryer Dock Dryer Vent 6″ for 4″ Tubes, White

Dryer Vent Made Easy eliminates the wasted space behind your dryer caused by bulky flex pipe. With Dryer Vent Made Easy, simply slide the dryer into the rubber seal in the wall without reaching behind to make the connection. It allows your dryer to push tight to the wall and flushes up the front of your washer and dryer. Our product increases your dryer’s efficiency and safety which saves you money and helps our environment. Welcome to the future of dryer vent installation. Made in the USA.

Product description

DRYER VENT PERISCOPE FROM 29″ TO 77″ WITH 2 1/2″ WALL CLEARANCE. WHIRLPOOL

From the Manufacturer

This item is designed to fit between the studs inside the wall. It does a great job of carrying the exhaust air through the top plate and into attic/floor space. You should use the 4″ aluminum vent to complete the run to the outside. This dryer vent rough-in system has (3) 2-1/2″ clearance telescoping sections that extend from 29″ to 77″. It also has one male snap-lock fitting, one female snap-lock collar and mounting strap, as well as all-metal rigid construction that meets most in-wall codes.

Arlington Industries DV1-1 Dryer Vent Exhaust Mounting Block, 1-Pack. 8 by 8-Inch dryer vent mounting block provides the secure, attractive and time-saving way to install dryer vents on new siding. kit comes complete with a low profile louver-type hood, a snap-together 4-Inch aluminum tube and a siding block with J-channel. fits all siding types: 1/2-Inch and 5/8-Inch step and Dutch lap. UV rated and weather-resistant for long outdoor life and also paintable to match any color scheme. installs before siding is up, overhang covers cut ends of siding for a clean neat look. to install: cut hole in substrate with 4-1/2-Inch hole saw, insert vent tube into opening, use screws to mount dryer vent to substrate through flanges, install siding, overhang on vent flange hides cut ends of siding.